Waring PC50 Specifikace Strana 7
- Strana / 62
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
1
1. Introduction
The 870ITPH Intelligent Transmitter converts pH, ORP, or Ion Selective Electrode
measurements to a 4 to 20 mA and/or digital output signal depending on the model selected and
the configuration implemented.
The analog only output version (Model 870ITPH-A) supports configuration, calibration, and
diagnostic troubleshooting locally at the front panel. The transmitter has one 4 to 20 mA dc
output which can be software configured (connected) to temperature compensated measurement,
uncompensated (absolute) measurement, or temperature.
The digital output version (Model 870ITPH-F) supports configuration, calibration, and
diagnostic troubleshooting locally at the front panel, via a PC-based configurator anywhere on the
signal leads, or from any I/A Series workstation via an Intelligent Transmitter Fieldbus Module.
The digital output version supports either digital only communication or a hybrid 4 to
20 mA dc/digital communication as configured. When operating in either of these modes, the
transmitter continuously outputs three digital measurement values: temperature compensated
measurement, uncompensated (absolute) measurement, and temperature. In the 4 to 20 mA
mode, you may assign the output to any one of the three measurement parameters.
Quick Start
The purpose of this section is to:
♦ Help you to wire your transmitter
♦ Familiarize you with the instrument configuration as received from the factory
♦ Assist you in verifying that your transmitter is in calibration
♦ Explain normal operation in Measure mode.
Wiring
Your 870IT is a 2-wire transmitter. As such, it transmits output over the same two wires through
which it receives power. If your transmitter was specified with analog communications
(870ITPH-A), you must supply its power source. If it was specified with digital communications
(870ITPH-F), power can be provided via the I/A Series Fieldbus Module. Connect this
power/output signal to the power terminals and the signals from your measurement sensor to the
appropriate terminals near the top of the case as shown in Figure 1.
WARNING
!
Wiring installation must comply with any existing local regulations.
WARNING
!
A safety agency certified energy barrier must be used with this apparatus to meet
agency certification requirements. See MI 611-206 (FM/CSA) or MI 611-208
(ATEX) for details.
- Instruction 1
- 870ITPH Intelligent 1
- Electrochemical Transmitter 1
- MI 611-211 – October 2005 2
- Contents 3
- 1. Introduction 7
- Factory Default Passcode 8
- Verifying Valid Measurements 8
- Reference Documents 9
- Specifications 10
- Identification 12
- 2. Installation 13
- Pipe Mounting 14
- Figure 7. Wiring 16
- 3. Operation 17
- Error Messages 18
- Passcode Access 19
- Viewing and Changing Data 19
- Diagnostics 21
- STATUS key 22
- STATUS at the top of your 22
- Configuration 23
- Config Output 24
- Config Electrod 25
- Config Tempcomp 25
- Config Temp 26
- Config Damping 27
- Config Chemcomp 27
- Config Instrmnt 27
- Config Timeout 28
- Config Buffers 28
- Config Passcode 31
- Config Strings 32
- Config AC Power 32
- Config Diags 32
- °C or °F). The 33
- (b)For PH10-.P or ORP10-.P 35
- Calibration 36
- Manual Calibration 37
- Automatic Calibration 37
- Electronic Calibration 38
- 4. Maintenance 41
- Top Level Structure Diagram 43
- Structure Diagram 1 44
- CONFIGURATION 44
- Structure Diagram 2 45
- CONFIGURATION (cont.) 45
- Structure Diagram 3 46
- Structure Diagram 4 47
- Structure Diagram 5 48
- Structure Diagram 6 49
- Structure Diagram 7 50
- Structure Diagram 8 51
- Structure Diagram 9 52
- CALIBRATION 52
- Structure Diagram 10 53
- CALIBRATION (cont.) 53
- Structure Diagram 11 54
- DIAGNOSTICS 54
- °C or °F 56
Související produkty a manuály pro ne Waring PC50
ne Waring WSC160 Uživatelský manuál
(2 stránky)
(2 stránky)
ne Waring WO50 Uživatelský manuál
(7 stránky)
(7 stránky)
ne Waring PC200 Uživatelský manuál
(8 stránky)
(8 stránky)
ne Waring PC100 Uživatelský manuál
(13 stránky)
(13 stránky)
ne Waring WPM40TR Uživatelský manuál
(1 stránky)
(1 stránky)
Brodit 511676 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Halter Brodit 511676.
Wir stellen 1 PDF-Handbücher Brodit 511676 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Halter Brodit
| Modelle | Dokumententyp |
|---|---|
| 511667 | Datenblatt Brodit 511667 holder, 2 Seiten |
| 634946 |
Datenblatt
Brodit ProClip 634946,
2 Seiten
|
| 511611 | Datenblatt Brodit ProClip 511611, 2 Seiten |
| 521631 | Datenblatt Brodit 521631 holder, 2 Seiten |
| 512606 | Datenblatt Brodit ProClip 512606, 2 Seiten |
| 511679 | Datenblatt Brodit 511679 holder, 2 Seiten |
| 511746 |
Datenblatt
Brodit 511746 holder,
2 Seiten
|
| 511653 | Datenblatt Brodit 511653 holder, 2 Seiten |
| 511652 | Datenblatt Brodit 511652 holder, 2 Seiten |
| 804832 |
Datenblatt
Brodit ProClip 804832,
2 Seiten
|
| 512746 |
Datenblatt
Brodit 512746 holder,
2 Seiten
|
| 834924 |
Datenblatt
Brodit ProClip 834924,
2 Seiten
|
| 655030 |
Datenblatt
Brodit ProClip 655030,
2 Seiten
|
| 834830 |
Datenblatt
Brodit ProClip 834830,
2 Seiten
|
| 513605 |
Datenblatt
Brodit ProClip 513605,
2 Seiten
|
| 834962 |
Datenblatt
Brodit ProClip 834962,
2 Seiten
|
| 511704 | Datenblatt Brodit 511704 holder, 2 Seiten |
| 511534 | Datenblatt Brodit ProClip 511534, 2 Seiten |
| 511635 | Datenblatt Brodit ProClip 511635, 2 Seiten |
| 513646 | Datenblatt Brodit 513646 holder, 2 Seiten |
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.014 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce